Sampling |
Sampling modes |
Normal sampling
Peak detection
Average value |
Sampling rate |
1GSa/s |
Input |
Input coupling |
DC, AC |
Input impedance |
1MΩ±2% connected in parallel with 20pF±3pF |
Probe attenuation coefficient |
1X, 10X, 100X, 1000X |
Max. Input voltage |
400V (peak) |
Channel delay time (typical) |
150ps |
Horizontal |
Sampling rate range |
100MS/s-1GS/s |
Waveform interpolation |
sin x / x |
Record length |
6K points on each channel |
Scanning speed range S/div |
5ns/div 5s/div, stepping in the “1-2.5-5” mode. |
Sampling rate and relay time
accuracy |
±100ppm(any time interval which is equal to or
larger than 1ms) |
Time interval
(T)measurement accuracy full bandwidth |
Single: ±(1 sampling interval
time+100ppm×reading+0.6ns)
>average 16 : ±(1 sampling interval time +100ppm×reading+0.4ns) |
Vertical |
Analog digital converter A/D |
With the resolution of 8 bits, make sampling on
both channels synchronously. |
Sensitivity range V/div |
5mV/div 5V/div at the input BNC |
Displacement range |
±50V(500mV 5V), ±1V(5mV 200mV) |
Analog bandwidth |
60MHz |
Single bandwidth |
Full bandwidth |
Low frequency response AD coupling,
-3dB |
≥5Hz at the BNC |
Rise time typical one at the BNC |
3.5ns |
DC gain accuracy |
±5% |
DC measurement accuracy average
value sampling mode |
The voltage difference (V) between any two points
on the waveform after averaging the captured waveforms more than16: ±(5%
reading + 0.05 divisions). |
Trigger |
Trigger sensitivity Edge triggering |
DC coupling : CH1 and CH2: 1div(DC full
bandwidth)
AC coupling : Same as the DC coupling when it is equal to or larger than
50Hz. |
Triggering lever range |
±6 divisions from the screen center |
Triggering level accuracy (typical)
which is applicable to the signal with rise and fall time equal to or
longer than 20ns |
±0.3 divisions |
Trigger displacement |
655 divisions for pre-triggering and 4 divisions
for post- triggering |
Make a 50% level setting (Typical) |
Operation with the input signal frequency equal
to or larger than 50Hz. |
Trigger sensitivity (Video
triggering and typical mode) |
2 divisions of peak-to-peak value |
Signal system and line/field
frequency (Video triggering mode) |
Support the NTSC, PAL and SECAM broadcasting
systems of any field or line frequency. |
Measurement |
Cursor measurement |
Voltage difference (V) and time difference (T)
between cursors |
Auto measurement |
Peak-to-peak value, average value, root mean
square value, frequency and cycle. |
Probe |
Bandwidth 1X position |
Up to 6 MHz (DC) |
Bandwidth 10X position |
Up to full bandwidth (DC) |
Attenuation rate 1 to 1 |
Compensation range |
10pf 35pf |
Input resistance |
1MΩ±2 |
Input impendence |
85pf 115pf |
Input voltage |
150 V DC |
Attenuation rate 10 to 1 |
Compensation range |
10pf 35pf |
Input resistance |
10MΩ±2 |
Input impendence |
14.5pf 17.5pf |
Input voltage |
300 V DC |
Display |
Display type |
3.8inch color liquid crystal display |
Display resolution |
640 (horizontal) × 480 (vertical)
pixels |
Display color |
65535 colors |
Power Adapter |
Power supply |
100-240 VACRMS, 50Hz, CAT II |
Power consumption |
< 6W |
Operating Temperature |
Used battery |
0 to 50 °C (32 to 122 °F) |
Power adapter |
0 to 40 °C (32 to 104 °F) |
Storage Temperature |
Storage |
-20 to +60 °C(-4 to +140 °F) |
Operating Humidity |
0 to 10 °C
(32 to 50 °F) |
no condensation |
10 to 30 °C
(50 to 86 °F) |
95 % |
30 to 40 °C
(86 to 104 °F) |
75 % |
40 to 50 °C
(104 to 122 °F) |
45 % |
Storage Humidity |
-20 to +60 °C
(-4 to +140 °F) |
no condensation |
Dimension |
180x113x40(mm) |
Weight |
645g |
Accessories |
Two 1:1 (10:1) passive oscilloscope
probes of 1.2 meters long
A pair of test leads of multimeter
A piece of serial-port data transmission line
A measuring extension module for small current
A measuring extension module for small capacitance
A power adapter in conformity with the standards of the host country
A user Manual
An operational optical disk
An aluminum case
※付属説明書、ソフトウェアは英語となります。 |